1. Forum
  2. Usenet
  3. SCI.ENGR.JOINING.WELDING

  • tig tutorial

    From F Murtz@21:1/5 to All on Sun Sep 5 23:39:32 2021
    As I said before I have a unimig similar to au unimig 190, it is not a dedicated tig machine it is mig tig and dc stick,I am trying tig without
    much sucess, every tutorial carrys on about specialised tig machines
    I wish instruction on basics voltage setting if applicable and current
    settings and how to without pedals, buttons fancy ignition,just scratch
    start and valve on handle for gas

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Richard Smith@21:1/5 to F Murtz on Mon Sep 6 20:27:37 2021
    F Murtz <[email protected]> writes:

    As I said before I have a unimig similar to au unimig 190, it is not
    a dedicated tig machine it is mig tig and dc stick,I am trying tig
    without much sucess, every tutorial carrys on about specialised tig
    machines
    I wish instruction on basics voltage setting if applicable and current settings and how to without pedals, buttons fancy ignition,just
    scratch start and valve on handle for gas

    TIG is a constant-current process like SMAW / "stick".
    You set the Amps only and Volts floats to what it does according to
    the Laws of the Universe.
    So you want to be on the setting for DC "stick".
    Regarding your set-up, I have to recall where I have used very
    improvised methods, and been admonished for not have the "proper" kit
    - yet got good results. So - I all sounds improbable, but by all
    means report back showing us you know where you are going with this.
    Best wishes,
    Rich Smith

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Charlie+@21:1/5 to F Murtz on Tue Sep 7 07:06:24 2021
    On Sun, 5 Sep 2021 23:39:32 +1000, F Murtz <[email protected]> wrote
    as underneath :

    As I said before I have a unimig similar to au unimig 190, it is not a
    dedicated tig machine it is mig tig and dc stick,I am trying tig without
    much sucess, every tutorial carrys on about specialised tig machines
    I wish instruction on basics voltage setting if applicable and current >settings and how to without pedals, buttons fancy ignition,just scratch
    start and valve on handle for gas

    Might this help! C+
    https://www.youtube.com/watch?v=--1lSmtuyUg

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Richard Smith@21:1/5 to [email protected] on Wed Sep 8 18:25:57 2021
    Charlie+ <[email protected]> writes:


    On Sun, 5 Sep 2021 23:39:32 +1000, F Murtz <[email protected]> wrote
    as underneath :

    As I said before I have a unimig similar to au unimig 190, it is not a >>dedicated tig machine it is mig tig and dc stick,I am trying tig without >>much sucess, every tutorial carrys on about specialised tig machines
    I wish instruction on basics voltage setting if applicable and current >>settings and how to without pedals, buttons fancy ignition,just scratch >>start and valve on handle for gas

    Might this help! C+
    https://www.youtube.com/watch?v=--1lSmtuyUg

    Met "6013 only" welding machines, for sure.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)