1. Forum
  2. Usenet
  3. REC.WOODWORKING

  • Proper bandsaw use

    From swalker@21:1/5 to All on Sun Nov 13 13:51:38 2022
    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    Thanks for any replies.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Scott Lurndal@21:1/5 to swalker on Sun Nov 13 20:20:51 2022
    swalker <[email protected]> writes:

    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    The blade guides should be just above the top of the stock. This
    reduces the tendency for a blade to wander laterally.

    It's possible that the videos you see are running with a non-optimal
    guide height for photographic purposes.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Keith Nuttle@21:1/5 to Puckdropper on Sun Nov 13 17:11:10 2022
    On 11/13/2022 4:54 PM, Puckdropper wrote:
    swalker <[email protected]> wrote in news:3di2nhtumh30p243dfu5au8lqr3cmf58gc@ 4ax.com:


    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    Thanks for any replies.

    You want to adjust that upper guide to just above your work, about a finger width or so above. It will add support to the cut and prevent cutting your hands on an accidental brush with the saw. (Don't rely on this: always pretend the blade is fully exposed!) It will also help confine the blade
    in case of a breakage.

    Your board may vary in thickness (especially if you haven't planed it) so setting the guide too low may result in the board hitting the guide. By setting it a finger width or so above you'll still have plenty of support
    and avoid this problem.

    Puckdropper
    The blade setting is very important, and while it may not prevent an
    accident, it can minimize the damage if an accident occurs, ie it could
    mean the difference between loosing a finger, and getting a bad cut.

    WHile not on a bandsaw, I got my finger into the blade of a table saw.
    Since I had the blade only about a 1/4" above the piece i was cutting
    the blade got into the flesh, but I still have a finger.



    --
    Judge your ancestors by how well they met their standards not yours.
    They did not know your standards, so could not try to meet them.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Puckdropper@21:1/5 to swalker on Sun Nov 13 21:54:54 2022
    swalker <[email protected]> wrote in news:3di2nhtumh30p243dfu5au8lqr3cmf58gc@ 4ax.com:


    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    Thanks for any replies.

    You want to adjust that upper guide to just above your work, about a finger width or so above. It will add support to the cut and prevent cutting your hands on an accidental brush with the saw. (Don't rely on this: always
    pretend the blade is fully exposed!) It will also help confine the blade
    in case of a breakage.

    Your board may vary in thickness (especially if you haven't planed it) so setting the guide too low may result in the board hitting the guide. By setting it a finger width or so above you'll still have plenty of support
    and avoid this problem.

    Puckdropper

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to swalker on Mon Nov 14 12:00:26 2022
    On 11/13/2022 1:51 PM, swalker wrote:

    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    Thanks for any replies.


    Answer number 4.

    A good bandsaw does not need guides at all.

    BUT the upper guides, set close to the top of the work, also adjusts the
    guard to protect your hand and fingers.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Jack@21:1/5 to Scott Lurndal on Sun Nov 20 09:26:02 2022
    On 11/13/2022 3:20 PM, Scott Lurndal wrote:
    swalker <[email protected]> writes:

    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    The blade guides should be just above the top of the stock. This
    reduces the tendency for a blade to wander laterally.

    It's possible that the videos you see are running with a non-optimal
    guide height for photographic purposes.

    Of course, then there is Sam Maloof....

    --
    Jack
    Tolerance is the virtue of the man without convictions.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to Jack on Mon Nov 21 11:29:14 2022
    On 11/20/2022 8:26 AM, Jack wrote:
    On 11/13/2022 3:20 PM, Scott Lurndal wrote:
    swalker <[email protected]> writes:

    I have always thought or assumed that the upper guides on the band saw
    should be close to the work and yet I see people on the Internet with
    the guides being 12 or more inches from the work.

    What is proper and why?

    The blade guides should be just above the top of the stock.  This
    reduces the tendency for a blade to wander laterally.

    It's possible that the videos you see are running with a non-optimal
    guide height for photographic purposes.

    Of course, then there is Sam Maloof....


    Was. ;~(

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)