In particular , for initial break-in . I've been reading up on the
proper lubes for initial run-in , and most recommend a lube - and motor
oil additive - with a lot of zinc . Others recommend moly for an initial
lube and don't say much about zinc additives . I have assembly lube that
has moly and graphite , or should I get the special zinc loaded stuff ?
--
Snag
My rights don't end
where your fear begins .

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On 2/20/2022 3:10 PM, Snag wrote:

In particular , for initial break-in . I've been reading
up on the proper lubes for initial run-in , and most
recommend a lube - and motor oil additive - with a lot of
zinc . Others recommend moly for an initial lube and don't
say much about zinc additives . I have assembly lube that
has moly and graphite , or should I get the special zinc
loaded stuff ?

I'm not an expert but this is good coverage on the issues: https://www.enginebuildermag.com/2013/05/assembly-oils-greases-and-lubes/

My engine guru of many years says Shell Rotella Diesel T4
with zinc engine oil for regular service and I do.

--
Andrew Muzi
<www.yellowjersey.org/>
Open every day since 1 April, 1971

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On 2/20/2022 16:51, AMuzi wrote:

On 2/20/2022 3:10 PM, Snag wrote:

In particular , for initial break-in . I've been reading
up on the proper lubes for initial run-in , and most
recommend a lube - and motor oil additive - with a lot of
zinc . Others recommend moly for an initial lube and don't
say much about zinc additives . I have assembly lube that
has moly and graphite , or should I get the special zinc
loaded stuff ?

I'm not an expert but this is good coverage on the issues: https://www.enginebuildermag.com/2013/05/assembly-oils-greases-and-lubes/

My engine guru of many years says Shell Rotella Diesel T4 with zinc
engine oil for regular service and I do.

I concur with the above. Also not an expert, but many old car guys like
Shell Rotella Diesel oil, and I usually hear people advising to use zinc additives for flat tappet cam engines.

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

In article <suuang$soa$[email protected]>, Snag <[email protected]> wrote:

In particular , for initial break-in . I've been reading up on the
proper lubes for initial run-in , and most recommend a lube - and motor
oil additive - with a lot of zinc . Others recommend moly for an initial
lube and don't say much about zinc additives . I have assembly lube that
has moly and graphite , or should I get the special zinc loaded stuff ?

The assembly lube isn't going to stick around on oil-submerged parts for
more than a minute anyway after the thing is operating. So long-term
issues like ZDDP content should not be a problem.

You ARE going to fill the crankcase up and cover the cams with oil before starting up, right? You're not going to rely entirely on the assembly
lube for lubrication until the oil pressure builds up, right?

So I wouldn't worry about it, I'd just use a motor oil with a lot of ZDDP,
or a motor oil with a ZDDP additive. I think Rotella T is a good choice
for break-in even if you're intending on moving to a synthetic oil with
a ZDDP additive later on.

I see assembly lubes with all kinds of stuff in them. I don't see any of
these as being a real advantage but if it makes you feel better to spend
an extra five bucks for an assembly lube with zinc in it, it won't hurt anything.

When those roller-cam engines were new, people were using things like
vaseline and used motor oil for assembly lubes. Or white lead mixed
into lard. Anything you can buy today is better quality than what the
engine was originally built with.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On 2/21/2022 8:18 AM, Scott Dorsey wrote:

In article <suuang$soa$[email protected]>, Snag <[email protected]> wrote:

In particular , for initial break-in . I've been reading up on the
proper lubes for initial run-in , and most recommend a lube - and motor
oil additive - with a lot of zinc . Others recommend moly for an initial
lube and don't say much about zinc additives . I have assembly lube that
has moly and graphite , or should I get the special zinc loaded stuff ?

The assembly lube isn't going to stick around on oil-submerged parts for
more than a minute anyway after the thing is operating. So long-term
issues like ZDDP content should not be a problem.

You ARE going to fill the crankcase up and cover the cams with oil before starting up, right? You're not going to rely entirely on the assembly
lube for lubrication until the oil pressure builds up, right?

I'll be driving the oil pump with a drill motor until I see oil
coming from all the right places . I should be able to push it all the
way to the rocker arms .

So I wouldn't worry about it, I'd just use a motor oil with a lot of ZDDP,
or a motor oil with a ZDDP additive. I think Rotella T is a good choice
for break-in even if you're intending on moving to a synthetic oil with
a ZDDP additive later on.

I see assembly lubes with all kinds of stuff in them. I don't see any of these as being a real advantage but if it makes you feel better to spend
an extra five bucks for an assembly lube with zinc in it, it won't hurt anything.

I'll use the assembly lube I've got , and continue to use Castrol GTX
but add a zddp additive .

When those roller-cam engines were new, people were using things like vaseline and used motor oil for assembly lubes. Or white lead mixed
into lard. Anything you can buy today is better quality than what the
engine was originally built with.
--scott

At least I've always used new oil ! Back in the day we didn't use
assembly lube , I don't even know if it was available then .
--
Snag
My rights don't end
where your fear begins .

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)